JK CEMENT WallMaxX WP33 is a White Cement based Wall Putty with excellent Water Resistance. It is
a factory controlled and very high quality product to properly cover undulations of the concrete and plastered surfaces. Also, it
provides very smooth finish, vital for successive painting stages. It is suited both for interior and exterior applications.
Properties | Results |
---|---|
Appearance | White Powder |
Composition | White Cement, Fine Graded Fillers, Re-dispersible Polymer powder and performance enhancing Additives |
Aggregate Size | >0.150 mm |
Compressive Strength* as per EN:1015-11 (28 days) |
>6 N/mm² |
Flexural Strength* as per EN:1015-11 (28 days) |
> 2.5 N/mm² |
Bond Strength* as per EN:1015-12 (28 days) |
≥ 1 N/mm² |
Water Retention* as per ASTM C1506 – 17 |
≥ 95 % |
Setting Time* at 25ºC | 7 -9 Hours |
Bulk Density | (Kg/Liter) 1 ± 0.10 |
Mixing Ratio | 6.6 – 7.6 Liters/20 Kg Bag & 8.3 – 9.5 Liters/25 Kg Bag |
Pack Size | 20 & 25 Kg Bags |
Application Thickness | Total Thickness of Maximum 3 mm in multiple layers |
Consumption | Approximately 1.25 – 1.75 m²/Kg * |
• All Surfaces should be thoroughly cleaned to remove dirt, oily stains, grease, loose particles, wood pieces, molds, etc.
• For previously painted/old painted substrates, scrub the layers with proper emery paper/wire brush so that it is free from these
old paint/dust particles.
• It should be mixed with clean water wherein gradual addition is essential.
• Mixing should be done in a clean plastic or non-corrosive metal bucket.
• It is recommended to mix it using an electric mixer fitted with proper paddle to achieve a good and homogeneous mixture.
• Mixing ratio is around 6.6 – 7.6 Liters of water per 20 Kg bag or 8.3 – 9.5 Liters of water per 25 Kg bag which can be adjusted
as per site application conditions.
• Once mixed, allow the mix to rest for about 5 minutes and just prior to application, mix it again without adding any extra water.
• Also hard and set paste should not be remixed or reused.
* Please refer to the Material Safety Data Sheet for more details.
• Prior to starting application, properly pre-wet the substrate with clean water.
• Gradually apply WP33 from bottom to top direction by pressing firmly over the substrate using steel trowel or suitable Putty
blades and properly level it to a smooth layer.
• The individual thickness per coat is not to exceed 1 mm for best results and ensure that total thickness should not exceed
3mm in multiple layers.
• Prior to application of the subsequent coat, please ensure that the previous coat is dried well.
• Mix only the needed quantities that are going to be applied to avoid any drying of the mixed material by time.
• Ensure to not use it on metal or any non-absorbing surfaces
• Refrain from application during rain, unstable weather conditions or under direct sun light.
• Once applied, any excess material needs to be removed with wet cloth before it dries and all application tools should be immediately cleaned with water
• To achieve surface even and remove application mark before applying paint use waterproof emery paper for sanding purpose.
• Shelf Life: 12 Months from date of manufacture if covered well and stored in pallets, away from heat, Sun light and moisture.
• Care should be taken that hard & lumpy materials are not to be used.
WP88 contains cement which becomes strongly alkaline upon mixing with water and this may cause skin irritation when exposed for very long time. Avoid contact with eyes and inhalation of dust. In case of skin/eyes contact, wash with plenty of clean water and seek medical attention immediately. It is highly recommended to use all relevant Personal Protective Equipment while handling it and work in well ventilated conditions while applying it. Keep out from the reach of children.
* Please refer to the Material Safety Data Sheet for more details.
Manufactured & Packed in UAE by
P.O. Box: 123630, The Citadel Tower, Office 2007-08, Business Bay, Dubai, UAE.
Tel : +971 4 279 7306 | Fax : +971 4 420 3906 | Email : sales.fuja@jkcement.com
www.jkcementuae.com
Date of Issue – May 2020
The information given here is based on the best of our knowledge, good faith, experience and laboratory based results. The actual result depends on many factors, like nature of substrate, workmanship/quality of the application job at site, quality and type of suitable application tool used, quantity of water added, etc. Hence JK Cement Works (Fujairah) is not responsible for any sort of claims/disputes arising out of any negative results by using our Products. Also, the water for dilution given here is only based on lab results and might vary due to different conditions prevailing at the application site. JK Cement Works Fujairah is not held responsible for use of this product for applications other than specified and/or adopting any faulty application/curing methodologies. It is the user’s responsibility to have through this Technical Data Sheet prior to applying our products and to ensure with JK Cement Works Fujairah that any product information is still prevailing at the time of application. Also the user must be sure that the product is suitable for the use intended and also applied it as specified while taking care of all precautionary measures. While all the products comply with the properties shown on current technical data sheets/brochures, JK Cement Works Fujairah does not warrant or guarantee the products’ performance as it doesn’t have any control over factors adopted during its actual application.