Sales.Fuja@jkcement.com
cement factories in uae

JK Cement WallMaxX – Finish Coat WP88

JK Cement's WP88

Product Description:

JK CEMENT WallMaxX WP88 is a White Cement based one component Finish Coat. This factory controlled product has a unique blend of composition, thereby properly filling pores, blowholes, minor honeycombs on the concrete and plastered surfaces. Also, it is a perfect skim coat to give smooth finish with an excellent aesthetic appeal which is vital for subsequent painting stages. It is suited both for interior and exterior areas.

Key Features:

  • Robust Bonding Strength and higher durability
  • Very Smooth and White Color Finish
  • Excellent Water Resistance

Application Areas:

  • Concrete, Pre-cast and Plastered Concrete substrates
  • Plastered Solid/Hollow Concrete Blocks
  • Plastered Light Weight/AAC Blocks
  • Areas like Kitchens, Bath rooms, etc. which are prone to be in water contact.

 

Properties Results
Appearance White Powder
Composition White Cement, Fine Graded Fillers, Re-dispersible
Polymer powder and performance enhancing Additives
Aggregate Size >0.150 mm
Compressive Strength* as per
EN:1015-11 (28 days)
>6 N/mm²
Flexural Strength* as per
EN:1015-11 (28 days)
> 2.5 N/mm²
Bond Strength* as per
EN:1015-12 (28 days)
≥ 1 N/mm²
Water Retention* as per
ASTM C1506 – 17
≥ 95 %
Setting Time* at 25ºC 7 -9 Hours
Bulk Density (Kg/Liter) 1 ± 0.10
Mixing Ratio 6.6 – 7.6 Liters/20 Kg Bag & 8.3 – 9.5 Liters/25 Kg Bag
Pack Size 20 & 25 Kg Bags
Application Thickness Total Thickness of Maximum 3 mm in multiple layers
Consumption Approximately 1.25 – 1.75 m²/Kg *

 

Surface Preparation

• All Surfaces should be thoroughly cleaned to remove dirt, oily stains, grease, loose particles, wood pieces, molds, etc.
• For previously painted/old painted substrates, scrub the layers with proper emery paper/wire brush so that it is free from these old paint/dust particles.

Mixing

• It should be mixed with clean water only.
• Mixing should be done in a clean plastic or non-corrosive metal bucket.
• It is recommended to mix using a low speed electric mixer fitted with proper paddle to achieve a good and homogeneous mix.
• Mixing ratio is around 7.5 – 8.5 Liters of water per 25 Kg bag which can be adjusted as per site application conditions.
• Once mixed, allow the mix to rest for about 5 minutes and mix it again without adding any extra water prior to application.
• Also hard and set paste should not be remixed or reused.

Application

• Prior to starting application, properly wet the substrate with clean water and ensure if it is damp while application.
• Gradually apply WP88 from bottom to top direction by pressing firmly over the substrate using steel trowel or suitable Putty blades and properly level it to a smooth layer.
• Ensure that the maximum thickness per coat is not to exceed 1.5 mm.
• If a second coat is needed, please ensure that the first coat is cured well and that the maximum thickness should not exceed 3 mm in total.
• If texture finish is needed, use damp sponges, plastic floats or other suitable tools. But care should be taken not to overwork the surface.
• Mix only the needed quantities that are going to be applied to avoid any drying of the mixed material by time.

Curing:

• After drying, the coated substrate should be cured with clean water for a minimum of 3 days with a frequency of 3 – 4 times a day.

Recommendations:

• Ensure to not use it on metal or any non-absorbing surfaces
• Refrain from application during rain, unstable weather conditions or under direct sun light.
• Once applied, any excess material needs to be removed with wet cloth before it dries and all application tools should be immediately cleaned with water
• To achieve surface even and remove application mark before applying paint use waterproof emery paper for sanding purpose.

Storage:

• Shelf Life: 12 Months from date of manufacture if covered well and stored in pallets, away from heat, Sun light and moisture.
• Care should be taken that hard & lumpy materials are not to be used.

Health & Safety:

WP88 contains cement which becomes strongly alkaline upon mixing with water and this may cause skin irritation when exposed for very long time. Avoid contact with eyes and inhalation of dust. In case of skin/eyes contact, wash with plenty of clean water and seek medical attention immediately. It is highly recommended to use all relevant Personal Protective Equipment while handling it and work in well ventilated conditions while applying it. Keep out from the reach of children.
* Please refer to the Material Safety Data Sheet for more details.

Manufactured & Packed in UAE by

Screenshot 2021-08-01 115410
P.O. Box: 123630, The Citadel Tower, Office 2007-08, Business Bay, Dubai, UAE.
Tel : +971 4 279 7306 | Fax : +971 4 420 3906 | Email : sales.fuja@jkcement.com
www.jkcementuae.com
Date of Issue – May 2020

Disclaimer:

The information given here is based on the best of our knowledge, good faith, experience and laboratory based results. The actual result depends on many factors, like nature of substrate, workmanship/quality of the application job at site, quality and type of suitable application tool used, quantity of water added, etc. Hence JK Cement Works (Fujairah) is not responsible for any sort of claims/disputes arising out of any negative results by using our Products. Also, the water for dilution given here is only based on lab results and might vary due to different conditions prevailing at the application site. JK Cement Works Fujairah is not held responsible for use of this product for applications other than specified and/or adopting any faulty application/curing methodologies. It is the user’s responsibility to have through this Technical Data Sheet prior to applying our products and to ensure with JK Cement Works Fujairah that any product information is still prevailing at the time of application. Also the user must be sure that the product is suitable for the use intended and also applied it as specified while taking care of all precautionary measures. While all the products comply with the properties shown on current technical data sheets/brochures, JK Cement Works Fujairah does not warrant or guarantee the products’ performance as it doesn’t have any control over factors adopted during its actual application.

Finish Coat | Cement Factories in UAE

Applications